Goulds J5S Shallow Well Jet Pump, 115/230 volt, 1/2 hp

Pipe connections: 1. 25" npt suction and 1" npt discharge, Pressure switch: AS4 preset 30-50 PSI. Compliant, food grade, injection molded, glass filled Lexan® for durability and abrasion resistance. Tubing and Fittings: F. D. A. Corrosion and abrasion resistant. Diffuser guidevane: Bolt down diffuser provides positive alignment with impeller.

Premium O-ringImpeller: F. D. A. Rotation: clockwise when viewed from motor end, UL778 listed. Resistant. Powered for continuous Operation: Pump ratings are within the motor manufacturer's recommended working limits. 60 hz, 1/2 hp, single phase, 115/230 v capacitor start, 3500 RPM. Built-in overload with automatic reset, Stainless steel shaft.

Can be operated continuously without damage. Corrosion resistant: Electro-coated paint process is applied inside and out, then baked on. Protected mechanical seal: Special diaphragm design retains water in the casing at all times to ensure the mechanical seal can never run dry. Excellent air handling ability: After initial priming the pump has the ability to re-prime itself even when air gets into the system.

Compliant, glass filled Noryl®.

---

Brands2O TC2104-P2 Well Pump Pressure Gauge

Brass fitting, Plastic housing and plastic lens. Measures from 0 to 100 psi. Flotec products are made to last and the Flotec TC2104 is no different. Also monitors water pressure. Use with submersible or jet pumps. The product fits easily into frac14;rdquo; female national pipe thread FNPT and can be easily installed for your convenience.

1/4-inch nPT connection size. Monitors the pumps performance. Itrsquo;s important to keep track of your jet or submersible pump to ensure good performance and to stay on track for tuneups and replacement needs. The flotec tc2104 will make your work easier by giving you a clear and concise reading of what your pump is doing at all times.

Easy to install and easy to use, yoursquo;ll enjoy having this pressure gauge around for a long time to come thanks to the tough materials itrsquo;s made from. About the flotec tc2104 pressure gauge for jet/submersiblewell and Sprinkler Pumps, 0100 PSI The Flotec TC2104 is a highperformance and highquality tool that allows you to monitor the performance of your jet or submersible well pumps.

This pressure control gauge features clearly marked PSI indicators that will tell you just how your pumps are doing at any given time.


Similar products

---

Square D by Schneider Electric FSG2J24CP 40-60 PSI Pumptrol Water Pressure Switch

Also monitors water pressure. 1/4-inch nPT connection size. Pressure connection. Use with submersible or jet pumps. The product is easy to use. The product is manufactured in china. The product is High durable and meets the customer requirement. 40-60 psi pumptroltM Water Pressure Switch. Brass fitting, Plastic housing and plastic lens.

40 - 60 psi. Standard-action contacts open on rising pressure. Monitors the pumps performance. 1/4 in. Suitable for jet pumps, submersible pumps and reciprocating pumps. Measures from 0 to 100 psi.


Similar products

---

Amtrol WX-202 Well Pressure Tank

Pressure switch settings should not exceed a 20 psi differential between cut in and cut out. 1/4-inch nPT connection size. It requires only a minimum of floor space and has an appliance-like blue finish allowing installation anywhere. Pressure connection. It is recommended to check tank pressure before installation.

Use with submersible or jet pumps. 40 - 60 psi. 40-60 psi pumptroltM Water Pressure Switch. High-strength Steel Shell. Note: all tanks are pre-pressurized at 38 psi and should always be set 2 psi below the cut in of your pressure switch. The stainless steel air valve is welded rather than threaded to prevent loss of air pressure.

1/4 in. Standard-action contacts open on rising pressure. Measures from 0 to 100 psi. Exclusive butyl diaphragm along with the 100% corrosion resistant virgin polypropylene liner are secured by a positive hoop ring seal for added strength and reliability. Virgin polypropylene inner Liner will not crack, chip, flake or peel.

Monitors the pumps performance. Brass fitting, Plastic housing and plastic lens.


Similar products

---

Square D by Schneider Electric FSG2J21CP 30-50 PSI Pumptrol Water Pressure Switch

Measures from 0 to 100 psi. Monitors the pumps performance. 40-60 psi pumptroltM Water Pressure Switch. 2 pole, ul/csa listed, diaphragm actuated, rohs compliant, 1/4" NPSF or internal pressure connection, NEMA 1 enclosure, NSF61-Annex G certified. Use with submersible or jet pumps. 30-50 psi pumptroltM Water Pressure Switch.

1/4 in. High-strength Steel Shell. Suitable for jet pumps, submersible pumps and reciprocating pumps. Virgin polypropylene inner Liner will not crack, chip, flake or peel. Unique positive hoop ring seal secures diaphragm and Liner for added strength and reliability. Clam shell packaging. Also monitors water pressure.

1/4 in. Water pump pressure switches suitable for use on all types of pumps including jet, submersible, and recriprocating. 1/4-inch nPT connection size. 30 - 50 psi. Pressure connection. Pressure connection. Brass fitting, Plastic housing and plastic lens.


Similar products

---

Square D FSG2J21M4CP 30/50 PSI Standard Pressure Switch with Low Pressure Cutoff

Pressure connection. 1/4-inch nPT connection size. Standard-action contacts open on rising pressure. 30-50 psi pumptroltM Water Pressure Switch. Measures from 0 to 100 psi. 30 - 50 psi. Monitors the pumps performance. For use with submersible well pumps or as a replacement switch. 1/4" - 18 npsf internal thread opening.

Unique positive hoop ring seal secures diaphragm and Liner for added strength and reliability. Suitable for jet pumps, submersible pumps and reciprocating pumps. They can be used for jet pumps, submersible pumps and reciprocating pump applications. 40-60 psi pumptroltM Water Pressure Switch. Virgin polypropylene inner Liner will not crack, chip, flake or peel.

Turns on at 30 psi and off at 50 psi. 40 - 60 psi. Pressure connection. 1/4 in. The square d pumptrol™ by schneider Electric Water Pressure Switches have been providing rugged, reliable performance for over 67 years. 1/4 in. Standard-action contacts open on rising pressure.


Similar products

---

Water Source Llc Rv50-nl 1/2-Inch Pressure Relief Valve No Lead 75 PSI

Not for use with water heaters. 30 - 50 psi. Pipe. For use with submersible well pumps or as a replacement switch. Brass fitting, Plastic housing and plastic lens. Solid-brass design meets federal low lead regulations. Suitable for jet pumps, submersible pumps and reciprocating pumps. 30-50 psi pumptroltM Water Pressure Switch.

1/2 in. The product is manufactured in china. Starts to relieve pressure at 75 PSI. For use with water-supply systems. 40 - 60 psi. Pressure connection. 1/4" - 18 npsf internal thread opening. 1/2 inch pressure relief valve, protects tank systems from excess pressure build up, preset at 75 psi, lead free. Use with submersible or jet pumps.

1/4 in. Standard-action contacts open on rising pressure. 1/4 in. Discharge port. 40-60 psi pumptroltM Water Pressure Switch. Pressure connection.


Similar products

---

WaterWorker HT20HB Horizontal Pressure Well Tank, 20-Gallon Capacity, Blue

The tank uses a thick diaphragm to keep water separate from pre-charged air and to help reduce air loss. The tank's steel shell with deep-drawn construction helps support water weight, while its polypropylene line helps prevent air and odors from being absorbed into the water. Pre-charged tanks are rated to compare with equivalent-size conventional standard tanks in terms of water drawdown between pump cycles.

Standard-action contacts open on rising pressure. Fits 1/2 in. The actual physical size of a pre-charged tank is much less and allows space savings up to 50% when comparing drawdown and size to that of a conventional tank. Pressure connection. Discharge port. The polypropylene liner for the water reservoir will not flake, chip, crack or peel and does not impart taste and odor to the water.

30-50 psi pumptroltM Water Pressure Switch. Not for use with water heaters. Use with submersible or jet pumps. 40 - 60 psi. A high gloss enamel finish protects tank from the elements. Monitors the pumps performance.


Similar products

---

Everflow BRBU1142-NL 1-1/4 Inch Male NPT X 1 Inch Female NPT Brass Lead Free Bushing, Fitting with Hexagonal Head, Brass Construction, Higher Corrosion Resistance Economical & Easy to Install

For use with water-supply systems. More economical than steel; certified to Meet NSF/ANSI 61-8 Standard for Quality Assurance. Pressure connection. 1/4" - 18 npsf internal thread opening. A high gloss enamel finish protects tank from the elements. It has npt threading for creating tighter seals than straight threads and is made from brass with a class 125, which is more economical and offers greater corrosion resistance than steel.

Npt thread for creating Tighter Seals Than Straight Threads. Turns on at 30 psi and off at 50 psi. Suitable for jet pumps, submersible pumps and reciprocating pumps. It has a hexagonal head for leverage and use with a wrench. This fitting are certified to meet NSF/ANSI 61-8 Standard for quality assurance. 40-60 psi pumptroltM Water Pressure Switch.

Protects tank systems From Excess Pressure Build Up. For electrically driven water pumps. Bushings are pipe fittings used to connect pipes of two different sizes. The everflow bushing is a brass pipe fitting with a hexagonal head and 1-1/4 Inch male National Piper Taper NPT threads on one end and 1 Inch female NPT threads on the other for connecting different types of pipe.

Monitors the pumps performance.


Similar products

---

WaterWorker HT-20B Vertical Pressure Well Tank, 20-Gallon Capacity, Blue

Standard-action contacts open on rising pressure. 1/2 in. Pipe. For use with water-supply systems. Heavy brass with stainless steel control springs. The butyl diaphragm has seamless construction and is designed to flex rather than stretch and crease like bladder tanks. 30-50 psi pumptroltM Water Pressure Switch. Discharge port.

Monitors the pumps performance. Solid-brass design meets federal low lead regulations. Npt thread for creating Tighter Seals Than Straight Threads. 1/4 in. Designed to keep pump starts to a minimum. This tank has a rated size of 42 gallons; the actual tank capacity is 20 gallons. 1/4 in. Brass fitting, Plastic housing and plastic lens.

Suitable for jet pumps, submersible pumps and reciprocating pumps. Capacity gal. 42, max. This separates air from water, preventing corrosion and bacterial growth-in compliance with FDA regulations. The actual physical size of a pre-charged tank is much less and allows space savings up to 50% when comparing drawdown and size to that of a conventional tank.




Similar products

---

Parts2O TC2505LF 1-1/4-Inch Check Valve

Standard-action contacts open on rising pressure. Designed to meet the requirements of, and are listed by the National Sanitation Foundation NSF under ANSI/NSF Std 61. Pipe. Standard-action contacts open on rising pressure. 1/2 in. The butyl diaphragm has seamless construction and is designed to flex rather than stretch and crease like bladder tanks.

Brass fitting, Plastic housing and plastic lens. The butyl diaphragm has seamless construction and is designed to flex rather than stretch and crease like bladder tanks. Turns on at 30 psi and off at 50 psi. Poppet style with stainless steel spring. For electrically driven water pumps. Diaphragm, liner isolate water from contact with deep drawn steel domed shell - twice as strong as rolled steel shell of same thickness.

1/4 in. A high gloss enamel finish protects tank from the elements. A high gloss enamel finish protects tank from the elements. Npt thread for creating Tighter Seals Than Straight Threads. 30 - 50 psi. Protects tank systems From Excess Pressure Build Up.


Similar products