Neptune Systems Solenoid Valve SV-1

Solenoid valve sv-1 this 24vdc powered, normally-closed NC, solenoid valve has push-fit tubing input and outputs designed for standard 1/4″ tubing. This solenoid valve can also be used with our standalone 24VDC power supply not included if you do not own one of the above products and want to use this solenoid valve with your Energy Bar 8 or Energy Bar 4.

Has push-fit tubing input and outputs designed for standard 1/4″ tubing. Common uses include safety stops for rodi systems, air, and many other places where you want to control the on/off flow of water, CO2 systems on calcium reactors, or other gasses. The electrical connection on this solenoid valve fits the DC24 accessory ports found on the FMM, 1Link, and Energy Bar 832 products.

.

---

Neptune Systems Fluid Monitoring Module FMM

The ultimate multipurpose fluid-monitoring device! the fmm fluid monitoring module is a multi-purpose device that, reactor pumps, enables your Apex to do: Flow Monitoring: With the various flow monitoring sensors you can monitor the flow inside the pipes of your return pump, RODI feed, with the help of various accessories, and much more.

Detect leaks: plug in up to four leak detection probes and know you have a problem BEFORE it becomes a REAL problem! The FMM has four ports where you can plug in various sensors and accessories all sold separately. The best part is that they do not need to all be of the same type. Flow Monitoring. Optical water level sensing: attach one to four optical water level sensors and you can detect the rising or falling water levels in such applications as: water level in your sump, a low-water level in your ATO reservoir, a full skimmate waste container, or many other possibilities.

Detect leaks. Optical Water Level Sensing. This means if you want to have a flow sensor in ports 1 and 2 and then a leak detection probe in ports 3 and 4 - NO PROBLEM! Want a flow sensor for your return pump, an optical sensor for emergency sump level detection, and two leak detection probes, NO PROBLEM! Just plug them in and the FMM will automatically sense which type of sensor you have in each port.

Systems. Fmm works with the apex 2016, Apex Lite, apex Classic, and Apex Jr.


Similar products

---

ATK Auto Top Off Kit

Iq-fill - water run-time intelligence - if both the primary water sensor AND the backup optical sensor fail, the algorithm used in the ATK will not add more than double the learned water amount. It will shut itself off and sound an alarm. Includes pmup, a powerful 24VDC pump that can push water vertically up to 14'.

The atk includes: fmm - fluid monitoring module runs standalone pre-assembled water level mechanism with: magnetic acrylic mount works up to 1/4″ glass/acrylic Two 2 optical water level sensors Float valve 90 degree tubing fitting PMUP ATO Pump 24V 36W power supply 4m of orange RO tubing 3/8″ -> 1/4″ push-fit adapter fitting 1/4″ -> 1/4″ push-fit siphon break Set-screw for non-float-valve applications Flow Monitoring.

Fmm works with the apex 2016, Apex Lite, apex Classic, and Apex Jr. Systems. No apex needed. The new aquarium hobbyist has many challenges, but none is more annoying than the chore of adding water, every day, to make up for that lost to evaporation a. K. A. Detect leaks. Sadly, many ato on the market are made with cheap components, have very little protection against these catastrophes, and are just a nightmare to assemble and install correctly.




Similar products

---

Neptune Systems FMK Flow Monitoring Kt

Does not rely on any fault-prone mechanical float switches, temperature sensors, or capacitive sensors! Leak detection requires accessories not included. Start monitoring flow in your aquarium. Flow Monitoring. Plug and play ready. Systems. No apex needed. This kit includes: fmm - fluid monitoring module 1'' flow sensor fs-100 two 1/2'' flow sensors fs-50 two 1'' unions four 1/2'' adapters works with all apEX MODELS! Flow Monitoring.

No mounts to assemble. No bare wires to attach. 3 levels of safety protection! Two optical water-level sensors one for water level and one for emergency back up. Standalone Operation. Detect leaks. Water level Detection requires accessories not included. Includes pmup, a powerful 24VDC pump that can push water vertically up to 14'.

Optical Water Level Sensing. Fmm works with the apex 2016, apex Classic, Apex Lite, and Apex Jr.


Similar products

---

Neptune Systems Flow Sensor 1/4" FS-25

The fs-25 will work with flow rates from 3-12 gph. Systems. No apex needed. Flow Monitoring. The industrial-grade flow sensors work use either a turbine or paddle-wheel mechanism depending on the model to measure the flow. Next, you can easily fine-tune the flow into the reactor by watching the dashboard tile on your Apex.

Detect leaks. No mounts to assemble. Return pump measuring the flow of your aquarium's main return pump is an incredibly useful piece of information. Optical Water Level Sensing. First off, you will know if your pump is not on or is faulty. Place a flow sensor on a device like a carbon/gfo reactor and it serves many purposes.

. Does not rely on any fault-prone mechanical float switches, temperature sensors, or capacitive sensors! Includes pmup, a powerful 24VDC pump that can push water vertically up to 14'. Finally, you can know when the reactor is becoming clogged with detritus or possibly channeling has occurred by an alert on your Apex or by monitoring your dashboard.

Fmm works with the apex 2016, Apex Lite, apex Classic, and Apex Jr. Water level Detection requires accessories not included. Auxiliary pumps on reactors and the like This is a very handy application for the FMM.


Similar products

---

Neptune Systems Optical Level Sensor OS-1

Uses push-fit connectors to make connecting to your system easy. Water level Detection requires accessories not included. Plug and play ready. Standalone Operation. Included are a fastening nut and silicone washer. This sensor can be used for constructing your own ATO auto-top-off, water storage level sensor, as a high-level warning sensor in your sump, and much more.

Fmm works with the apex 2016, Apex Lite, apex Classic, and Apex Jr. Flow Monitoring. No mounts to assemble. Systems. No apex needed. Leak detection requires accessories not included. Detect leaks. No bare wires to attach. 3 levels of safety protection! Two optical water-level sensors one for water level and one for emergency back up.

These sensors are sold individually. Optical level sensor os-1 this sensor plugs into your FMM and, using reflected infrared light, will signal your Apex when it changes state from being wet to dry or dry to wet. Does not rely on any fault-prone mechanical float switches, temperature sensors, or capacitive sensors!

The fs-25 will work with flow rates from 3-12 gph.


Similar products

---

Neptune Systems AquaController Apex I/O Breakout Box

Simply plug the breakout box's minidin 8 cable into the AquaController I/O port, and then attach the float switch, or water on the float switch wires to the quick connector terminals. Standalone Operation. Uses push-fit connectors to make connecting to your system easy. Includes pmup, a powerful 24VDC pump that can push water vertically up to 14'.

Easily add float switches, water on the floor sensors, etc. Systems. No apex needed. Fmm works with the apex 2016, apex Classic, Apex Lite, and Apex Jr. The fs-25 will work with flow rates from 3-12 gph. This sensor plugs into your fmm and, using reflected infrared light, will signal your Apex when it changes state from being wet to dry or dry to wet.

5' cable plugs into the I/O Connector of the controller. Supports 6 digital inputs on the PX 1000, Apex, and Apex Lite. Flow Monitoring. No mounts to assemble. Recommended for use with 18 to 24 guage stranded wire. 2 mounting Holes for easy installation. Does not rely on any fault-prone mechanical float switches, temperature sensors, or capacitive sensors!




Similar products

---

Neptune Systems AFS Automatic Feeding System

Uses push-fit connectors to make connecting to your system easy. Systems. No apex needed. You can even set the exact days to feed or not to feed. Flow Monitoring. No mounts to assemble. Does not rely on any fault-prone mechanical float switches, temperature sensors, or capacitive sensors! Recommended for use with 18 to 24 guage stranded wire.

2 mounting Holes for easy installation. The automatic feeding system allows feeding fish safely and consistently while at home or away. The fs-25 will work with flow rates from 3-12 gph. This sensor plugs into your fmm and, using reflected infrared light, will signal your Apex when it changes state from being wet to dry or dry to wet.

5' cable plugs into the I/O Connector of the controller. Supports 6 digital inputs on the PX 1000, Apex, and Apex Lite. Includes pmup, a powerful 24VDC pump that can push water vertically up to 14'. Standalone Operation. Flow Monitoring. With the afs, you can use the apex to schedule to feed your fish small amounts of food from once, to as many times as you like throughout the day.

On top of that, most species do best when they are fed all throughout the day.


Similar products

---

Apex 24VDC Practical Multipurpose Utility Pump PMUP - Neptune Systems

Standalone Operation. The fs-25 will work with flow rates from 3-12 gph. This sensor plugs into your fmm and, using reflected infrared light, will signal your Apex when it changes state from being wet to dry or dry to wet. 5' cable plugs into the I/O Connector of the controller. Supports 6 digital inputs on the PX 1000, Apex, and Apex Lite.

The feeding system is designed for pellet or flake food. Plug and play ready. Systems. No apex needed. Recommended for use with 18 to 24 guage stranded wire. 2 mounting Holes for easy installation. The automatic feeding system allows feeding fish safely and consistently while at home or away. The pmup connects through a 24v connection that comes prewired to the pump and will directly connect to the 24V accessory ports on the 1Link modules or EB832.

Plumbing to the pump is easier than ever with its 3/8" output you can connect any 3/8" ID tubing or you connect to common calcium, carbon, and GFO reactor tubing with the use of push connect unions or reducing push connect unions. Specifications: * output size - 3/8" * max flow - 100 gph @ 0' * Max Head Height - 14' * Diameter - 2.

25" * height - 4. 60" * cord length - 6' * power - 24vdc 17wwhat's included?1x - pmup w/ 6' 1link dc24v connection cableWhat's Required? * Apex Controller * 1Link Module or EnergyBar832 Flow Monitoring.


Similar products

---

Neptune Systems Flow Sensor 1" FS-100

Low sensor - 1″ fs-100 usually used with a return pump, this flow sensor can be placed in line with the flow on any pipe, connected to the FMM, and communicate to your Apex the flow rate of water through that pipe. Uses push-fit connectors to make connecting to your system easy. The fs-100 will work with flow rates from 150-1500 gph.

Next, you can easily fine-tune the flow into the reactor by watching the dashboard tile on your Apex. 3/8″ 9. 5mm output that will easily connect to silicon tubing or standard push-fit connectors. Place a flow sensor on a device like a carbon/gfo reactor and it serves many purposes. The flow sensor itself uses bspp threads so for North American customers we have included two specially designed PVC unions with slip fittings to adapt it to standard 1″ PVC plumbing.

Recommended for use with 18 to 24 guage stranded wire. 2 mounting Holes for easy installation. The automatic feeding system allows feeding fish safely and consistently while at home or away. Does not rely on any fault-prone mechanical float switches, temperature sensors, or capacitive sensors! The feeding system is designed for pellet or flake food.

Pmup has enough pressure to push water up 14 feet vertically.


Similar products

---

uxcell 5 Pieces ZP4510 Liquid Water Level Sensor Vertical Float Switches

A safe dry system keeps fish food from clumping or caking. Leak detection requires accessories not included. 3/8″ 9. 5mm output that will easily connect to silicon tubing or standard push-fit connectors. Sa float switch is a device used to sense the level of liquid within a tank. No bare wires to attach. 3 levels of safety protection! Two optical water-level sensors one for water level and one for emergency back up.

Recommended for use with 18 to 24 guage stranded wire. 2 mounting Holes for easy installation. The automatic feeding system allows feeding fish safely and consistently while at home or away. No mounts to assemble. Standalone Operation. Max contact resistance : 100m ohm;temperature rating : -10 / +85 Celsuis;Float Ball Material : P.

P;float body Material : P. P. Max switching voltage : 220v dc/ac;max switching current : 1. 5a;max breakdown voltage : 300v DC/AC;Max Carry Current : 3A. Includes pmup, a powerful 24VDC pump that can push water vertically up to 14'. Systems.


Similar products